Kitchen cabinets are indispensable for every family. Cabinets are an important part of each kitchen renovation. There is a great deal of knowledge about the measurement of cabinets. The following describes the contents of the cabinet door size measurement method by Xiao Bian, so that you can have a set of desirable cabinets.
Cabinet door size measurement method
1. When measuring the length, it is best to measure twice, from left to right and from right to left, so as not to read the wrong size for the first time.
2. When measuring the ceiling height, measure the quasi-high points in several different directions, and at the same time, see if there are no beams under the gusset plate.
3, the measurement depends on the waist, the height of the mobile socket to the floor tile, while looking at the window height (retest should pay attention).
4. Measure the distance and height from the gas meter and the pipe to the wall, the height of the flue, the height of water in and out of the water, the distance from the drainage supervisor to the wall, and the height of the socket (retest).
5, when the measurement depends on whether there are steps on the ground, the wall has no bumps and beams, when the edge of the window to do wall cabinets to consider the pull of screens, such as the relevant to the cabinet to measure the relevant size.
6, when the re-test to brick shop, wall stickers, such as hanging cabinets or high cabinet to the top of the ceiling to be re-tested.
7. It is better to select the fixed point and the diagonal when measuring the profiled or polygonal shape. When the two sides are close to the wall to make the cabinet (ground, hanging cabinet), they must also measure the distance between the inside and the outside.
8, when there is a poor brick to measure the distance to the wall and the height (including the height of the bottom and the top to the ground), the best refrigerator position is best to stay 700MM long, special additional length.
9, where there is a door cover to measure the thickness of the door cover and good (including lines), or a sliding door, hanging cabinet to open and pull the door but also to stay 10-20MM gap.
10, such as the unit of measurement of the kitchen, you should pay attention to ask whether the wall is a stone wall, so as not to install the wall cabinet.
Buy cabinets considerations
Note one: Consider buying the whole cabinet should start before the renovation
Because the installation of kitchen cabinets and kitchen decoration is one, the kitchen is different from the living room and other places. Do not purchase cabinets for installation after renovation. The correct method is: before the renovation, please cabinet manufacturers to measure, set the cabinet style model, set aside the pipeline interface and the corresponding space, and then carry out renovations, and finally the cabinet manufacturers to enter the construction.
Note two: cabinet selection should be reasonable and effective
Some people fear that the storage space in the kitchen will be insufficient. Therefore, they prefer to choose cabinets with more cabinets. The choice of cabinets does not lie in how much better, but should be reasonable and effective. Too many cabinets not only take up part of the activity area, but also make the kitchen appear to be heavily depressed.
Note three: Select the cabinet panel, to identify the board density
When choosing panels, people often only pay attention to their appearance and surface properties. They only look at whether the outer surface is waterproof, fireproof, and scratch-free, but they neglect the inner “heart†quality. The most direct way to discern the sheet density is to ask the sales person to take out the panel model and observe whether the cross-section particles are tight.
Note four: hardware accessories to see the brand
In all kinds of furniture, cabinets should be regarded as the most frequently used. The quality of hardware accessories directly determines the quality and service life of the cabinet. Therefore, when customizing cabinets, it is not desirable to use poor quality products in order to save money. When choosing a cabinet, you may wish to first look at the hardware brands it uses.
Note 5: Range hood height should be reasonable
In order to enhance the function of range hoods, many people think that the hood is as close to the stove as possible. In fact, the effective distance of the range hood is usually 80 cm, and the smoking effect is almost the same in this range. Therefore, the range hood can be installed on the basis of the height of the owner. The height of the hood is usually about 80 cm and should not be too high or too low.
Xiao Bian summary : The cabinet door size measurement method and the related content of the cabinet cabinet attention are introduced first, and I hope to help you. More exciting information is on this site.
Cabinet Door Size Cabinet Warranty Cupboard Size Cabinet Standard Size Cupboard Cabinet Size
WIND TOWER FLANGE MATERIAL AVILALBE :
Carbon steel Alloy steel High Stainless
A515GR 65 S355JR / A182F304/A240 304
A515GR 70 S355NL / A182F304L/A240 304L
A516GR 60 Q345A/b / A182F316/A240 316
A516GR 70 / A182F316L/A240 316L
S235JR / / A182F321/A240 321
Wind Tower Flange,S355Jr Wind Tower Flange,Wind Power Ring,Wind Tower Rolling Ring
HeBei GuangHao Pipe Fittings Co .,LTD (Cangzhou Sailing Steel Pipe Co., Ltd) , https://www.guanghaofitting.com