The test camera mainly tests sharpness and color reproduction, illumination, and backlight compensation, followed by measurement of ball distortion, power consumption, and minimum operating voltage. The following first measurement steps for sharpness and color reproduction and illumination and backlight compensation introduce.
1, the measurement of sharpness
When multiple cameras are used for testing, the same lens should be used (it is recommended to use fixed focus and two variable lenses). The center circle of the test card appears on the right and left sides of the monitor screen, and the given scale is clearly and accurately counted. The line consists of 10 vertical lines and 10 horizontal lines. Represents vertical resolution and horizontal resolution, respectively, and the corresponding set has given the number of lines. For example, the vertical 350 line level 800 line, at this time it is best to use a black and white monitor. The test can focus on distant objects or focus on the edge. It is best to use both, and you can see the differences in this camera (for far and near convergence).
2, color reproduction test
Test this parameter should choose a good color monitor. First observe the characters and costumes from a distance to see whether there is color distortion or not. Compare the objects with vivid colors. Look at the sensitivity of the camera. Take the color picture book in front of the camera. Look at the picture clearly, too light or too thick, and respond to the motion again. The color objects are photographed for color smearing, lag, blur, etc. The test conditions such that the maximum illuminance of the camera at 50V should be measured under the condition of 50+10V illuminance, that is, plus ten volt on the basis of the most illuminance of each camera, and the aperture should be kept in the closest state.
3, illumination
The camera is placed in a dark room. Before and after the dark room, there is an active 220V self-firing lamp. A voltage regulator is provided at the place to adjust the darkness of the dark room lamp with the voltage regulator to adjust the voltage. The voltage can be adjusted from 0V to 250V. The indoor illumination can also be adjusted from the darkest to the brightest. When the camera's aperture is maximized during the test, the next lowest illuminance value is recorded (the active light regulator is dimmed to a position where the dark interior is not visible). Hit the minimum and then record the next minimum illuminance value.
4, backlight compensation
There are two ways to test this parameter: one is in the dark room, turn on the front lamp of the camera, turn it to the brightest, and then place a picture or text below the lamp to take the camera to the light to see the image and Whether the text can be seen, the screen is not harsh, and adjust the AL, AX gear switch to see if there is a change, which effect is best. The other is to take the camera out of the window when the sun is shining. At this time, you can see if the image and text are clear.
5, spherical distortion
Look at the ball-type distortion and place the test card on the front of the camera so that the entire sphere appears on the screen. See whether the sphere has an ellipse or not. Move the camera forward to see if the center of the circle is magnified, and then test whether the edges, corners, and boxes have arcs at a long distance. Shape distortion and so on.
6, power consumption
Minimum operating voltage, use a multimeter to measure current, and use a small regulator to adjust the voltage.
1, the measurement of sharpness
When multiple cameras are used for testing, the same lens should be used (it is recommended to use fixed focus and two variable lenses). The center circle of the test card appears on the right and left sides of the monitor screen, and the given scale is clearly and accurately counted. The line consists of 10 vertical lines and 10 horizontal lines. Represents vertical resolution and horizontal resolution, respectively, and the corresponding set has given the number of lines. For example, the vertical 350 line level 800 line, at this time it is best to use a black and white monitor. The test can focus on distant objects or focus on the edge. It is best to use both, and you can see the differences in this camera (for far and near convergence).
2, color reproduction test
Test this parameter should choose a good color monitor. First observe the characters and costumes from a distance to see whether there is color distortion or not. Compare the objects with vivid colors. Look at the sensitivity of the camera. Take the color picture book in front of the camera. Look at the picture clearly, too light or too thick, and respond to the motion again. The color objects are photographed for color smearing, lag, blur, etc. The test conditions such that the maximum illuminance of the camera at 50V should be measured under the condition of 50+10V illuminance, that is, plus ten volt on the basis of the most illuminance of each camera, and the aperture should be kept in the closest state.
3, illumination
The camera is placed in a dark room. Before and after the dark room, there is an active 220V self-firing lamp. A voltage regulator is provided at the place to adjust the darkness of the dark room lamp with the voltage regulator to adjust the voltage. The voltage can be adjusted from 0V to 250V. The indoor illumination can also be adjusted from the darkest to the brightest. When the camera's aperture is maximized during the test, the next lowest illuminance value is recorded (the active light regulator is dimmed to a position where the dark interior is not visible). Hit the minimum and then record the next minimum illuminance value.
4, backlight compensation
There are two ways to test this parameter: one is in the dark room, turn on the front lamp of the camera, turn it to the brightest, and then place a picture or text below the lamp to take the camera to the light to see the image and Whether the text can be seen, the screen is not harsh, and adjust the AL, AX gear switch to see if there is a change, which effect is best. The other is to take the camera out of the window when the sun is shining. At this time, you can see if the image and text are clear.
5, spherical distortion
Look at the ball-type distortion and place the test card on the front of the camera so that the entire sphere appears on the screen. See whether the sphere has an ellipse or not. Move the camera forward to see if the center of the circle is magnified, and then test whether the edges, corners, and boxes have arcs at a long distance. Shape distortion and so on.
6, power consumption
Minimum operating voltage, use a multimeter to measure current, and use a small regulator to adjust the voltage.
Car Parking Device,Parking Device,Hot Sale Car Parking Device,Car Parking Device For Sale
Taiyaun JDS Machinery And Equipment Co., Ltd. , https://www.jdsmachine.com