Jumei Indian Home Furnishing Museum     Meihao Home Accessories Museum
Illness 1: Cracking and shedding of the coating
Cause: The coating showed cracks like hair filaments in the early stages and exfoliated in the later stages. Most of them used coatings with poor adhesion and flexibility, excessive dilution or coating materials, and the surface of the wall or base was not pretreated. Full, excessive hardening and embrittlement after film aging.
Recommendation: Remove loose and peeling paint with a spatula or wire brush, sand the surface and trim. If spalling occurs on multiple coats, water-resistant putty should be used if necessary.
The primer must be closed before recoating. The use of good quality primers and topcoats can prevent the recurrence of such problems. Do not over-dilute the paint with water.
Illness 2: Mildew
Cause: Black, gray, or brown spots appear on the surface of the paint or wall surface where moisture, light or light are not in direct contact (such as baths, kitchens, laundry rooms, etc.). Before the use of inferior emulsion paint or coating, the substrate or the coating on the coating was not cleaned.
Recommendation: Place a few drops of household bleach in the area of ​​discoloration to detect the presence of mold. If the stain disappears, it may indicate mold. Wipe the surface with a diluted household bleach solution (one part bleach to three parts water) to completely remove the mold. Rinse thoroughly with rubber gloves and goggles while working. To avoid mildew on the walls, use a regular manufacturer's high-quality latex paint. If necessary, use a bleach/detergent solution to clean the substrate. Consider installing the exhaust fan in a high-humidity area.
Illness 3: Coat wrinkles
Cause: When the paint is applied, the paint is thick at one time and the surface of the paint film becomes rough and wrinkled. Brushing in very hot or cold weather causes the surface of the paint film to dry faster than the bottom layer, exposing the uncured coating film to an excessively humid environment, and brushing the contaminated surface (if dust or oil is present) Thing).
Recommendation: Wipe or polish the surface of the substrate to remove the wrinkled coating. If you apply a primer, make sure the primer is completely dry before applying the top coat. When brushing again (to avoid extreme temperatures and humidity), apply a uniform layer of high-quality interior paint.
Illness 4: Yellowing of the coating
Cause: Ordinary paints are often exposed to sunlight. After coming from above the furnace, heating, heating pipes, or other materials, yellowing is likely to occur. This is due to UV aging and oxidation of other substances.
Recommendation: For strong sunlight or vulnerable areas, it is recommended to use high-quality anti-aging, light-resistant latex paint for decoration.
Construction Acceptance Paint Buy Three Trees Lacquer Paint Lacquer Home Heating Home Furnishings
We supply various fitting light (fitting lamp), including Led Purification Fixture, LED Tube Light Fixture, LED Split T8 Tube, T5 LED Tube Light etc.
The below information will help you to know more about fitting light.
What is used for light fitting?
Aluminum is used in light fitting design either as casted aluminum, extrusions or sheet metal. Many alloys are commonly used.
How many types of tube lights are there?
Fluorescent tubes (officially known as "lamps") come in five basic types, identified as T2, T5, T5HO, T8, and T12, and The "T" designation stands for "tubular," and the following number refers to its diameter in 1/8-inch diameter increments. 1 A T12 bulb, for example, is 12/8 inch in diameter, or 1 1/2 inches.
T5 and T8 are the popular ones.
T5 (16mm Diameter)
T5 tubes have a diameter of 16mm. They can be used to illuminate anything from schools to underground railways. They're an ideal choice for illuminating large spaces because they typically last up to 20,000 hours, they also have a low mercury content, limiting environmental impact. T5s have a high quality light output and colour rendering.
T8 (26mm Diameter)
T8 tubes have a diameter of 26mm. They can be used in schools, garages, offices, retails stores and most other environments. They have excellent colour rendering and can last up to 42,000 hours. Versions available now include LED Tube Lights and standard gas filled tubes
Fitting Light,Fitting Lamp,Bedroom Light Fittings,Wall Light Fittings
NINGBO LONGFLIGHT INTELLIGENT TECHNOLOGY CO.,LTD , https://www.long-flight.com