1. Barrier cannot be activated 1) Check whether the barrage is provided with mains electricity (given city electricity)
2) Check if the fuse of the barrier control box is in good condition (replace the fuse)
3) Check whether the wiring is correct, whether the connection terminal wiring is in good contact, and whether the control box plug is inserted correctly;
4) Check if the timing belt is in good condition (replace the timing belt)
5) Motor failure (replacement of motor)
6) Failure of the control box (replacement of the control box)
7) Failure of the drive capacitor (replacement of capacitor 2 and lift can not be reduced 1) Check the manual button is intact (replace manual button)
2) Check whether the photoelectric switch outputs the signal in place after the barrier is lifted into position (replace the photoelectric switch)
3) Check whether the manual button wire is broken (excluding the disconnection phenomenon)
4) The motor trips and starts the power line (open circuit)
5) If with infrared protection device, check whether the infrared protection receiver has a protection signal output (adjust the infrared protector or replace the infrared protector)
6) If there is a sense of protection, check if it is dead (reset)
7) Failure of the control box (replacement of the control box)
3, the barrier can not drop 1) check the manual button is intact (replace the manual button)
2) Check whether the photoelectric switch outputs a signal when the barrier is lowered to position (replace the photoelectric switch)
3) Check whether the manual button wire is broken (excluding the disconnection phenomenon)
4) Failure of the control box (replacement of the control box)
5) The electric motor is lifted and the power line is disconnected (excluding the disconnection phenomenon)
4. The brake lever is shaken during the lifting process of the barrier gate 1) Check whether the reducer base is loose (correction gear)
2) Check if the transmission gear is intact (replace the transmission gear)
3) Check if the spindle bearing is damaged (replace the bearing)
4) Check if balance spring is damaged (replace spring)
5) Check whether the connecting rod starts in the opposite direction (adjust the motor wire and control wire)
5ã€Do not stop at the gate 1) Damage to the photoelectric switch (replace the photoelectric switch)
2) On-position pull-out lever on photoelectric switch (replacement of photoelectric switch puller)
3) Poor contact of photoelectric switch connector (rework connector)
4) The open circuit between the photoelectric switch and the control box is disconnected (excluding the disconnection phenomenon)
5) Failure of the control box (replacement of the control box)
6, non-stop after the Daozha in place 1) damage to the photoelectric switch (replacement of photoelectric switch)
2) On-position pull-out lever on photoelectric switch (replacement of photoelectric switch puller)
3) Poor contact of photoelectric switch connector (rework connector)
4) The open circuit between the photoelectric switch and the control box is disconnected (excluding the disconnection phenomenon)
5) Failure of the control box (replacement of the control box)
7, Barrier stop after power transmission 1) Failure of the control box (replacement of the control box)
8. In the course of using the barrier, the main body of the barrier is shaken. 1) Open the barrier gate door and tighten the barrier bolt.
9. When the barrier is up and down, the brake lever cannot be vertical or parallel. 1) Open the barrier cover and adjust the photoelectric switch up and down.
10. Barrier remote control found insensitive during use. Remote control distance is short. 1) Remote control battery is low (replace battery)
11. The speed is too slow when the ramp lifts, and it cannot be started with a little external force. 1) Damage to the drive capacitor (replacement of capacitance)
2) Motor coil damage (replace motor)
2) Check if the fuse of the barrier control box is in good condition (replace the fuse)
3) Check whether the wiring is correct, whether the connection terminal wiring is in good contact, and whether the control box plug is inserted correctly;
4) Check if the timing belt is in good condition (replace the timing belt)
5) Motor failure (replacement of motor)
6) Failure of the control box (replacement of the control box)
7) Failure of the drive capacitor (replacement of capacitor 2 and lift can not be reduced 1) Check the manual button is intact (replace manual button)
2) Check whether the photoelectric switch outputs the signal in place after the barrier is lifted into position (replace the photoelectric switch)
3) Check whether the manual button wire is broken (excluding the disconnection phenomenon)
4) The motor trips and starts the power line (open circuit)
5) If with infrared protection device, check whether the infrared protection receiver has a protection signal output (adjust the infrared protector or replace the infrared protector)
6) If there is a sense of protection, check if it is dead (reset)
7) Failure of the control box (replacement of the control box)
3, the barrier can not drop 1) check the manual button is intact (replace the manual button)
2) Check whether the photoelectric switch outputs a signal when the barrier is lowered to position (replace the photoelectric switch)
3) Check whether the manual button wire is broken (excluding the disconnection phenomenon)
4) Failure of the control box (replacement of the control box)
5) The electric motor is lifted and the power line is disconnected (excluding the disconnection phenomenon)
4. The brake lever is shaken during the lifting process of the barrier gate 1) Check whether the reducer base is loose (correction gear)
2) Check if the transmission gear is intact (replace the transmission gear)
3) Check if the spindle bearing is damaged (replace the bearing)
4) Check if balance spring is damaged (replace spring)
5) Check whether the connecting rod starts in the opposite direction (adjust the motor wire and control wire)
5ã€Do not stop at the gate 1) Damage to the photoelectric switch (replace the photoelectric switch)
2) On-position pull-out lever on photoelectric switch (replacement of photoelectric switch puller)
3) Poor contact of photoelectric switch connector (rework connector)
4) The open circuit between the photoelectric switch and the control box is disconnected (excluding the disconnection phenomenon)
5) Failure of the control box (replacement of the control box)
6, non-stop after the Daozha in place 1) damage to the photoelectric switch (replacement of photoelectric switch)
2) On-position pull-out lever on photoelectric switch (replacement of photoelectric switch puller)
3) Poor contact of photoelectric switch connector (rework connector)
4) The open circuit between the photoelectric switch and the control box is disconnected (excluding the disconnection phenomenon)
5) Failure of the control box (replacement of the control box)
7, Barrier stop after power transmission 1) Failure of the control box (replacement of the control box)
8. In the course of using the barrier, the main body of the barrier is shaken. 1) Open the barrier gate door and tighten the barrier bolt.
9. When the barrier is up and down, the brake lever cannot be vertical or parallel. 1) Open the barrier cover and adjust the photoelectric switch up and down.
10. Barrier remote control found insensitive during use. Remote control distance is short. 1) Remote control battery is low (replace battery)
11. The speed is too slow when the ramp lifts, and it cannot be started with a little external force. 1) Damage to the drive capacitor (replacement of capacitance)
2) Motor coil damage (replace motor)
Plasma Consumables Compatible for Kjellberg
We have plasma cutting consumables for PB-S45W Plasma Consumables,Hifocus 280i Plasma Consumables,Percut-100 Plasma Consumables.Hifocus 360i Plasma Consumables Compatible for Kjellberg.
Our Plasma Consumables are made by imported high-quality copper and use superb CNC technology. So they got bright surface and cutting speed, less wear and tear, as compared with the original product, we can reach 90%. But our low prices, it is worth buying.
PB-S45W Plasma Consumables,Hifocus 280i Plasma Consumables,Percut-100 Plasma Consumables.Hifocus 360i Plasma Consumables
EDAWELD COMPANY LIMITED , https://www.jsedaweld.com