Solenoid valve selection guidance

Solenoid valve selection basis: First, according to the selection of solenoid valve parameters: Path Specifications (ie, DN), interface mode (connection) 1, in accordance with the size of the pipe diameter or flow requirements to determine the path (DN) size. 2, the interface mode, the general DN> 65 to choose the flange interface, DN ≤ 65 can be free to choose according to user needs threaded or flanged. Second, select the solenoid valve according to the type of medium: body material, sealing material, temperature group 1, corrosive fluid: Body material should use stainless steel or PTFE (polytetrafluoroethylene, commonly known as plastic king), and optional fluorine rubber or PTFE sealing material. 2, food or ultra-clean fluid: Body material should use sanitary stainless steel, and optional silicone rubber seal material. 3, high temperature fluid: To choose the use of high temperature stainless steel and sealing material manufacturing solenoid valve, but also to choose the principle of piston-type structure. 4, the fluid state: as large as a gaseous, liquid or mixed state, especially when the larger diameter must be distinguished because it is related to the pilot hole parameters. 5, fluid viscosity: usually below 50cSt can be arbitrarily selected, if more than this value, you need to use high viscosity solenoid valve. 6, fluid cleanliness: media containing impurities in the solenoid valve installed before the optional other structures. Third, select the solenoid valve according to the level of pressure: Principle Structure Type 1, nominal pressure: This parameter and other common valve meaning is the same, is based on the pipe nominal pressure or use pressure 1.5 times to set. 2, the working pressure: refers to the solenoid valve is closed, the valve front-end pipeline pressure minus the valve back-end pipeline pressure values ​​obtained; when no pressure, low pressure, vacuum, you must use direct acting or straight Dynamic principle, but the direct acting caliber can not be selected too much; when you have a certain pressure above the choice of pilot principle structure. (Our pilot-piston solenoid valve structure as long as 0.01MPa working pressure will be able to work). Fourth, the power supply voltage options: try to give priority to commonly used AC220V, DC24V more convenient. Fifth, according to the length of work or special needs to choose the control mode: normally closed, normally open, self-sustaining, emergency cut off (manual reset) 1, when the solenoid valve needs a long time to start, and continued to open much longer than the time Close time, should use normally open type. 2, if the opening and closing frequently switch or open a short time or open, close time, then choose the normally closed type. 3, but some for security conditions, such as furnace flame monitoring, gas leak alarm, fire safety linkage system, you should choose to cut off the solenoid valve emergency, but not long-term power supply type (long-term power is only a relative concept) Can not choose the more often open. 4, Self-holding solenoid valve (also known as: bistable) is a new technology, it is mainly used for energy-saving or low voltage drive applications. Six, according to environmental requirements to choose auxiliary functions: Explosion-proof, check back, manual, water fog, water pouring, diving 1, flammable, explosive environment: the appropriate level of explosion-proof solenoid valve must be selected (our product explosion mark: EXD Ⅱ CT5. , When the pipeline medium backflow phenomenon, you can choose our ZC series with check function solenoid valve. 3, when the need for on-site manual operation of the solenoid valve, you can choose our company ZC series with manual function solenoid valve. , Open-air installation or dust occasions should choose waterproof, dustproof varieties (protection grade above IP45.) For fountain or underwater pipeline must be used submersible solenoid valve (protection level above IP68).

Pool Lights

LEDER technology`s LED pool light is specifically designed to replace incandescent bulbs in swimming pool underwater light fixtures. Installing a 12 Volt bulb into a 120 Volt socket may permanently damage your pool's lighting system. The brightness of colors is up to 2x brighter than other cheaper bulbs. All colors can fill the whole pool. Multiple lamps can be synchronized to change color. 16 color mode: 7 brilliant fixed colors, 9 dazzling light show press the button in the remote controller to directly select the color you want.

LED pool light is used for swimming pools, water sports fields, ocean activity areas and so on.We insist on independent design, independent research and development.LED pool light is a much required lighting solution.

Features:

• Independent design

• It has high water resistance

• Energy province electricity

• Contracted design

• Color temperature :3000k-6000K

• Type of protection: IP20 /IP65 (Some models)

• Warranty:3 - 5 years

LED pool light is known for its energy efficiency and durability.We have a series of LED pool lights to show you, which will meet your requirements for activities in the water.

We have rich production experience in lighting .Except LED Pool Light, we also offered other product in Outdoor Lighting ,such as LED Flood Light , LED street Light , LED Inground Light, LED Spike Light ,LED Bollard Light ,Outdoor Wall Light & Step Light as so on .

Floating Pool Lights,Swimming Pool Lights,Solar Pool Lights ,Above Ground Pool Lights

JIANGMEN LEDERLIGHT LIGHTING Co.,LTD , https://www.spikelights.com