Doors are often used by every family. The installation of the door seriously affects normal life, so care must be taken during the installation process. In order to avoid the inconvenience caused by the repair and return to the factory lock, I hope that everyone can firmly grasp the knowledge of the wooden door installation brought by the decoration home decoration network Xiaobian!
First check whether the components of the wooden door are complete, whether the dimensions of the components are correct, and whether the positions of the sets of doors to the corresponding installation are consistent with the size of the door opening.
1. Assemble the door cover and find the door cover and the vertical plate first. According to the back number, the joint should be on the same plane. Apply glue to the interface and put 80mm wood screws on the hole behind the interface. Tighten it with a screwdriver. Do not put the screw directly into the entry sleeve. Check that the size between the nozzles is correct. The joint is flat and firm. Then install the iron on the back of the door panel and install the iron. To use 25mm self-tapping screws, the spacing of the iron pieces should be 300-350mm, and the iron piece should be 200mm from the ground.
2. Install the door cover and put the assembled door cover into the door hole as a whole. Fix the door cover around with the small wooden strip. The two sides of the door cover should be on the same plane as the wall. Then check whether the whole door cover is perpendicular to the ground. Whether the two corners of the top plate and the two vertical plates are at right angles, whether the door cover vertical plate is bent or not, the iron pieces are twisted at both ends to wrap the wall. According to the position of the reserved hole on the iron piece, drill the 8mm hole on the wall with the electric hammer, plug it with a small wooden strip, fix the iron piece to the wall with 80mm wood screws, and then use the small wooden strip to fix the door cover and the wall. The gap between the bodies is filled tightly, and the door cover is re-checked for compliance with the door, and then the styrofoam is inserted.
3. Install the door leaf to open the hinge groove first. The distance between the hinge groove and the door leaf is 1/10 of the height of the door leaf. The heavier door should be equipped with 3 hinges. The depth of the hinge groove is the hinge piece. The thickness is suitable. When installing the hinge, use the screw matched with the hinge. The screw should be tightened with a screwdriver. The screw can not be directly driven by the hoe. After the hinge on the door is fixed, the hinge on the door cover should be only Screw on a screw, then close the door to check whether the left and right gaps of the door are the same. If the opening is flexible, confirm the correctness and tighten the other screws.
4. Install the door lock to the corresponding position according to the provided lock type. The height of the lock position is 900-1000mm from the ground. After installation, check whether the door leaf and door lock switch are flexible and whether the seam is in compliance with the specifications.
5. Install the door sleeve line according to the size of the installation site. Cut the door sleeve wire saw with right angle edge into a 45 degree bevel, trim it with a flat or woodworking planer, insert it into the door pocket with a right angle, and use the floor glue to cover the door. Sticking to the door panel, the angle of the 90 degree tip is consistent, flat, and the seam is tight. The seam of the door sleeve is glued firmly. At the ends of the door sleeve, the corner nail is a small nail. Fix it.
6. Install the door suction at the corresponding position.
1, the mouth is consistently good.
2. The door leaf and door lock switch are flexible.
3. The left, right and upper gaps of the door leaf are the same. The specific dimensions are: 3--4mm on the left and right, and 8--12mm on the ground.
4, the door cover vertical set plate should be perpendicular to the ground level, no bending and twisting phenomenon.
5. The door sleeve line is in close contact with the wall surface.
6, the decorative surface is not damaged.
7. After cleaning, the full set of solid wood doors (cleaned on site) will be installed and submitted to the user for acceptance. The user will be introduced to the maintenance method.
I believe that after reading the above contents brought by the decoration home decoration network Xiaobian, everyone has a general understanding of how to install the wooden door ! Of course, if you are not in a hurry to install, it is best to contact a dedicated installer, safety is still the first! For more related knowledge, please also pay attention to our decoration encyclopedia section!
4014 Led Chip,4014 White Color Led Chip,White Color Led Chip,4014 Smd Led Chip
Shenzhen Huangtai Photoelectric Co.,Ltd. , https://www.huangtailightstrip.com