Today, Xiao Bian came to tell you about some maintenance cleaning tips for automatic sorting scales.
Maintenance cleaning Automatic sorting scales are mainly divided into the following four steps:
1, clean automatic sorting scales:
After disconnecting the power of the automatic sorting scale, unplug the power cord. Soak the gauze, wring it out, and use a little neutral detergent (such as alcohol) to clean the weighing pan, display the filter, and other parts of the scale. Conveyor belts that can be easily handled can be washed with warm water. Approximately 45°C warm water is cleaned once a week, the automatic sorting scale belt is soaked in boiling water for about 5 minutes, and the printer is cleaned (if the equipment is equipped with a printer):
Cut off the power, open the plastic door on the right side of the scale body, hold the plum handle on the outside of the printer, and pull the printer out of the scale body. Press the front of the printer, loosen the print head, and gently wipe the print head with the special print head cleaning pen attached to the scale attachment. After cleaning and wiping, wipe the pen cap inside the anti-pen cleaner to volatilize, and wait for two minutes until the print head is ready. After the cleaning liquid has fully evaporated, close the print head, push the printer back into the scale body, close the plastic door, and check the electricity. After clear printing, it can be used normally.
3, the host part of the clean:
1. After the power supply must be cut off, prevent the danger of electric shock, and then start cleaning the weight sorter 2. Select the cleaning tools. Use water or a neutral detergent to clean the cloth. 3. Do not use thinners, benzene, etc. Organic solvents - to prevent corrosion of objects and body, affect the use of 4, do not use metal brushes to prevent scratches on objects and the body 4, automatic sorting scale maintenance:
1, due to the touch and fingerprints caused by pollution, etc., neutral detergent can be used or soap can not be completely removed, can be used organic solvents (alcohol, gasoline, acetone, etc.) sponge or cloth to wipe 2, due to cleaning agent adhesion If the rust is caused and it cannot be removed with a neutral detergent, use a cleaning solution 3, rust caused by iron powder or salt during the operation of the machine, and use a sponge containing neutral detergent or soapy water or The cloth is wiped and can be easily removed and wiped clean
Tips:
After using a neutral detergent or hypochlorous acid solution, wash it thoroughly with clean water. If the cleaning solution is left behind, it may cause early deterioration of the belt and affect the weighing equipment. use.
I System description:
Heat Shrinkable Tape is designed to protect the weld joint of buried or exposed steel pipelines and insulated pipeline. This sleeves are manufactured from high quality cross linked polyethylene material. Hot melt adhesive provides excellent adhesion with the surface of steel pipeline, PE coating. Meanwhile it forms a continuous and firm anti-corrosive system with the surface of the pipeline.
The Polyethylene Heat shrinkable Tape needs no primer nor patch closure and reduces application time and labour costs.
â…¡ Structure
The specification of the tape consists of three layers,
Adhesive: butyl rubber based hot melt adhesive
Film backing: Radiation crosslinked polyethylene
Interleaf:Antiadhesive Film Treated with Silicone
â…¢ Features
After heating, formed corrosion protection seal
Strong backing provides outstanding waterproofing effect
High chemical resistance. resists impact, abrasion and ultraviolet light.
Excellent resistance against cathodic disbondment, dielectric breakdown.
Simple Application
â…£ Physical Properties
· Product Data Sheet Total Thickness:40mil, 50 mil,60 mil ,65 mils.
· Width:50,100,150,300,400,500,800 mm
· Length: 10 m
· Tensile Strength:35 N/cm
· Elongation:400%
· Adhesion Strength to pipe:30 N/cm
· Application temperature: -10 -60 ℃
· Temperature resistance:-50 ℃ - 80℃
· Shelf Life: 12 months
â…¤ Application
No Special skills, equipments, patch closure nor primer are needed. Its superior flexibility provides easy and reliable application for irregular configurations of fittings, bends and elbows and small diameter of straight pipes
Wrap spirally the tape over foreign matters-free and preheated surface, beginning at least 25~50mm (1~2 ) onto pipe coating. Wrap the tape with enough tension to obtain conformability and with minimum 50% of overlapping, while removing the release liner. Warm the end part of the tape and press down firmly. Using a torch, start at the edge of the tape and heat circumferentially around the coated pipe.
Finish off by heating over the entire tape vertically to ensure a uniform adhesion and by using a roller or gloved hands to remove wrinkle and air.
VI. Technical Datas
Heat Shrinkable Tape
Heat Shrinkable Tape, Shrink Wrap Tape, Heat Applied Tape
Jining Xunda Pipe Coating Materials Co.,Ltd , http://www.pipe-wrap.com