How to make normal protection of wheel bearings

Source: Bearing network time: 2018-04-19

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

Hub bearing is how to do the general protection summary: CNC machine tool production and use of data management system Autodesk for the operation of customers to introduce the most comprehensive treatment program lathe economical numerical control system hardware depicting compound cycle cutting command outer diameter roughing composite cycle G71 command large space Three-dimensional laser scanning system CNC lathe processing spherical error analysis and elimination method Fine punching skills in car production Al-Mg and Al-Cu alloy aluminum arc welding electrode selection How to use the intermediate tool length to compensate the function General machinery industry standard English and Chinese Comparison Table (2) Processing Intermediate Processing Specification The first automatic wide-band gear splitting machine in China talks about the selection of inverter capacity and the useful method of processing the bottleneck of auto parts processing. Ten suggestions for improving the efficiency of CNC milling machine. Skills development and prospects CNC machine tool analysis case analysis analysis of the involute tooth profile processing principle gas cutting profile protection normal bearing if the view of the brake smooth transition tire wheel bearing car important walking machine wheel bearing bearing negative chassis work conflict resistance Keep the car normal Traveling heavy-duty wheel bearing problems can lead to noise bearing heat appearance, especially the front wheel is more significant and simple, causing the direction of out-of-control risk bearing wheel bearing needs to be protected as scheduled. See the wheel bearing for wheel hub bearings.
Wheel bearing is an important moving part of the car. The wheel bearing bears the conflict resistance when the chassis is lowered; the burden of keeping the car running normally. If the wheel bearing is out of order, it can cause noise, bearing heat, etc.; especially before The wheel is more significant; it simply leads to risk signs such as out of control. Therefore, the hub bearing needs to be protected as scheduled.
1. View of the hub bearing (1) When viewing the tightness of the hub bearing; firstly, the axle of the wheel at one end of the wheel of the car is inspected; the vehicle is safely framed with a vehicle stool, a wooden cover, etc.
(2) Change the number of wheels to be inspected by hand; see if the transition is stable; whether there is abnormal noise. If the transition is unstable and there is a conflicting sound; clarify that the brake is not normal, if there is no noise; Smooth and tight when tight; clarify that the bearing is somewhat abnormal. The wheel should be removed when the above abnormal image is presented.
For small cars; when looking at the hub bearings; grasp the upper and lower sides of the tires with both hands; pull the tires back and forth with both hands; repeat it repeatedly. If it is normal; there should be no feeling of looseness and blockage, if it is shaken, it is significantly loose. Feeling; the wheel should be dismantled.
(3) Viewing the brakes. Usually when viewing the wheel bearing; check the wheel brake equipment by the way; if there is oil on the inside of the tire; it can be caused by the oil leakage of the brake cylinder or the brake oil pipe; Clear reason; to be removed.
2. The protection of the hub bearing is before the hub is disassembled; the preparation of the hub protection should be done; the car should be stopped and the axle should be set up to ensure the safety of the protection operation.
(1) Remove the embellishment cover and dust cover of the hub shaft head.
(2) Remove the tire nut and tire; pay attention not to hurt the thread of the tire bolt. If it is a disc brake; remove the brake; then use the pliers to remove the lock ring or lock pin.
(3) Remove the hub with a special tool,
(4) scrape off the old smooth grease in the bearing, journal and hub cavity; use the scavenger to remove the hub bearing and journal and wipe it with a cloth; finally wipe the inner cavity of the hub with a cloth.
(5) Look at the hub bearing and the bearing race; find the appearance of cracks, fatigue and looseness of the bearing roller; replace the bearing. If it is found that there is pitting on the bearing race; also replace the bearing.
(6) Check the cooperation between the inner diameter of the bearing and the journal; the cooperation gap should not be greater than 0. 1Omm when measuring the journal; it should be measured in the upper and lower parts of the vertical ground (the largest wear part is where it is). The application limit of the rule; the bearing should be replaced; the normal cooperation gap should be restored. It is not allowed to burr and pitting on the journal to reduce the gap.
(7) After all the parts meet the requirements; the inner bearing is smoothed and put into the wheel hub.
(8) Care should be taken when changing the inner cavity of the bearing to smooth grease; the smooth grease should be squeezed into the bearing until the smooth grease emerges from the other side of the bearing. A thin layer is applied in the hub cavity and the shaft cap. Smooth grease; make it anti-rust effect. Pay attention to the smooth grease in the hub cavity, do not change too much; otherwise it will affect heat dissipation and braking.
(9) Put the hub and outer bearing back on the journal; screw the shaft adjustment nut by hand; then tighten the adjusting nut with the shaft wrench according to the regular torque. After tightening the nut; turn the wheel a few turns left and right; The condition of the bearing device, on the other hand; after the transformation, the bearing and the seat ring cooperate correctly. At this moment, the bearing tightness is appropriate; the wheel is free to change and no axial gap is felt.
(10) The final sequence of locking devices, fixing nuts, tires, dust cover and embellishment cover and other parts.
(11) After the hub bearing is adjusted; travel a distance (about 1Okm); parking view; temperature used to wipe the hub; if it is hot; caused by over-tightening of the bearing; should be adjusted from the beginning; properly loosen the bearing tightness .

Recommend to friends comments close window

Bearing related knowledge

NSK bearing repair method analysis of rolling mill bearing device and protection of key turbines in the operation of the bearing temperature increase in the detailed analysis: "working in the bearing" should pay attention to the industrial bearing protection and installation methods

This article links to http://
Please indicate China Bearing Network http://

Previous:The bearing that is damaged by the offset press Next edit: Bearing fatigue life test

High Mast Lights

High Mast Lights,High Mast Lights Pole,High Mast Light

China Searun Solar Solution Co., Ltd. , https://www.srsolarlights.com