Variable pump piston pump in the daily use of the process, it is inevitable that there will be no fault, then the variable piston pump common faults what? Cause there? With these questions, the next for you Introduction variable piston pump common faults and what are the reasons. Variable piston pump common faults and causes 1. Hydraulic pump output flow is not enough or not output fluid (1) Insufficient inhalation. The reason is that the resistance of the oil suction pipe is too large or the amount of oil is insufficient. Such as the pump speed is too large, the tank surface is too low, into the tube leakage, filter plug and so on. (2) the amount of leakage is too large. The reason is the pump gap is too large, caused by poor sealing. Such as oil pan with metal fragments, iron filings and other scratches, face oil spills; variable mechanism in the check valve sealing surface with poor pump and oil pan bearing surface with trachoma or scratch and so on. Can check the pump body of hydraulic oil in the foreign material to identify the pump is damaged parts. (3) The tilt angle of the swash plate is too small, and the displacement of the pump is small. This requires adjusting the variable piston and increasing the inclination of the swash plate. 2. Median oil displacement is not zero Variable axial piston pump swashplate tilt is zero when the median is called, then the pump output flow should be zero. However, there is a tendency for the center to deviate from the midpoint of the adjustment mechanism and there is still flow output at the midpoint. The reason for this is that the controller is out of position, loose or damaged, requiring zeroing, fastening or replacement. Insufficient pump force to maintain the angle of the trunnion wear will have this phenomenon. 3. Output flow fluctuations Output flow fluctuations and many factors. The variable pump can be regarded as the poor control of the variable mechanism, such as foreign body into the variable mechanism, the control piston on the draw marks, wear marks, scars, etc., resulting in control piston instability. Due to insufficient energy in the amplifier or damaged parts, the damping effect of the spring-containing control piston is poor, resulting in unstable control piston motion. Flow instability is often accompanied by pressure fluctuations. Such failures generally open the hydraulic pump, replace damaged parts, increase damping, improve the spring stiffness and control pressure. 4. Abnormal output pressure The pump output pressure is determined by the load, and the input torque is approximately proportional. There are two types of output pressure abnormalities. (1) the output pressure is too low When the pump in the self-priming state, if the leakage of oil into the pipeline or hydraulic cylinder in the system, one-way valve, valve and so have a larger leak, will make the pressure rise. This requires finding leaks, tightening, and changing seals to increase pressure. Pressure relief valve or adjust the pressure is low, the system pressure also does not increase, the pressure should be re-adjusted or overhaul relief valve. If there is a large amount of leakage due to the deviation between the cylinder of the hydraulic pump and the valve plate, in severe cases, the cylinder may rupture. Then, grind the mating surface or replace the hydraulic pump. (2) the output pressure is too high If the loop load continues to rise, the pump pressure continues to rise, it is normal. If the load is constant and the pump pressure exceeds the pressure required by the load, check the hydraulic components other than the pump, such as the directional valve, pressure valve, transmission, and return line. If the maximum pressure is too high, should adjust the relief valve. 5. Vibrations and Noise Vibrations and noise occur simultaneously. They not only endanger the machine operator but also pollute the environment. (1) Mechanical vibration and noise If the shaft of the pump and the motor shaft are not concentric or dead, the shaft bearing, coupling damage, pad damage and loose assembly bolts will produce noise. For high-speed operation or transmission of large energy pump, to regularly check and record the amplitude of each component, frequency and noise. If the frequency of rotation of the pump is the same as the natural frequency of the pressure valve, it will cause resonance and change the speed of the pump to eliminate the resonance. (2) the noise generated by the pipeline flow into the oil pipeline is too small, into the oil filter flow capacity is too small or blocked, the intake pipe into the air, the oil is too high, the oil surface is too low oil shortage and high pressure pipe In the liquid hammer and so on, will produce noise. Therefore, the correct design of the fuel tank, the correct choice of oil filters, tubing and directional valve. 6. Hydraulic pump overheating Hydraulic pump overheating for two reasons, one is mechanical friction heat. Due to the dry or semi-dry friction surface, the moving parts friction and heat. Second, liquid friction heat. High-pressure oil leaks into the low pressure chamber through various gaps, and a great deal of hydraulic pressure can be lost to heat energy. Therefore, the correct choice of moving parts between the gap, the tank volume and cooler, can prevent excessive pump heat and oil temperature is too high. In addition, back to the oil filter blockage caused by back pressure too high, will cause the oil temperature is too high and the pump overheating. 7. Oil spill piston pump oil leakage mainly for the following reasons: (1) the spindle oil seal damaged or shaft defects, scratches; (2) the internal leakage is too large, resulting in increased pressure at the seal, and the oil seal damage or out ; (3) the drain pipe too thin, so that the seal leaks; (4) pump external tubing loose, pipe joints damage, seal aging or crack; (5) variable adjustment mechanism bolts loose, seal damage; Cast iron pump casing with trachoma or poor welding. Extended reading: China Construction Water Exhibition water pump manufacturers rankings ptc exhibition motor top ten brands pump valve pipe fittings Show Information Industry Internet (Xiamen) Technology Co., Ltd. Asia Pump Network Editor: He Duanhui (QQ / WeChat:) http: // mj .liuti.cn / (Service Hotline:)
Fujitec Escalator Spare Parts, Fujitec Escalator Parts
Fujitec has been devoted to manufacturing high-quality, reliable escalators in harmony with municipal scenery and buildings. It designs and develops the quick, quiet, smooth, safe, and reliable GS-NX series of escalators with complete functions, pursues the individualized escalator production and realizes the optimum locomotion system.
Fujitec Escalator Spare Parts,Fujitec Escalator Parts,Fujitec Escalator Contactor Spare Parts
CEP Elevator Products ( China ) Co., Ltd. , https://www.zjelevatordoorsystem.com