Buying a house has always been a major event in home life. How to accept a house that has bought a lot of silver and bought it has become a concern of many people. Then, what should be paid attention to when ordinary buyers who have no professional experience check and accept? In the mid-term acceptance of the house, what are we to accept? In fact, mainly for the acceptance of rough and concealed works, the acceptance results will largely affect the next steps, we have specially collected the tips of the home inspection experts , share the precautions for house acceptance with everyone, and then follow the decoration home network Xiaobian to learn about the housing acceptance related content!
During the mid-term acceptance period, in addition to the overall effect of the decoration, it is mainly to judge the satisfaction of the project quality. If there is dissatisfaction or new ideas at this time, some local changes can be made at this time, if the decoration It will be very troublesome to change after you finish. Specific acceptance can be identified from the following aspects.
First, the acceptance link
1. Whether the acceptance lighting circuit is laid in accordance with the specifications, whether the socket, the lamp switch, the main gate, the leakage switch, etc. have a certain height. In addition, the kitchen and air conditioner must be laid by special lines, and the antenna and telephone line of the TV should be installed in a position convenient for maintenance.
2. Check whether the drainage is smooth, there is no leakage, backflow and water accumulation. Check the high-grade water parts without pinching and wiping.
3. Whether the new wall is vertical, consistent with the horizontal plane of the brick, the joints are even and tidy, the brick joints are not more than 1mm, the overall error of the flat ceiling is not more than 0.5mm, the gap between the plates and the plates is not more than 0.3mm; the error of the plastic ceiling is not More than 0.5mm.
4, the wall surface and the plane in a straight line, no obvious convexity and chromatic aberration within one meter, the paint should be smooth, feel good, no obvious color difference and nail holes.
5. The seam of the wooden sealing line, the corner line and the waist line panel shall not exceed 0.2mm, the angle between the line and the line shall not exceed 0.3mm, the touch panel and the plate shall not exceed 0.2mm, and the whole surface of the sliding door shall not exceed the error. 0.3mm.
Second, the acceptance tool
In the process of home decoration, acceptance is a very important part. In time, the hidden problems and deficiencies in the decoration are found. In addition to the rich experience, the corresponding auxiliary tools should be prepared. Here are some of the necessary magic weapons and their usages.
1, tape measure
The tape measure is used to measure the net height, the net width of the house, and the size of the cabinet. When the actual inspection, it is necessary to pay attention to whether the reserved space is reasonable, and whether the size of the cabinet is consistent with the original design.
2, vertical detection rule
The vertical detection ruler is a detection tool with a high frequency of use in home improvement inspection. It is used to detect whether the wall surface, the tile is flat, and whether the floor keel is horizontal.
3, feeler feet
The feeler gauge is mainly used to detect the size of the gap, and the head of the feeler gauge is tightly inserted into the slit to exit. The size of the travel code is the size of the gap, and it is checked whether it meets the requirements.
4, diagonal detection rule
Place the ruler on a square object and measure the diagonal line to check the deviation of the two diagonal lengths.
5, square ruler
It is used to detect the verticality and levelness. It is mainly used to test whether the corners of the corners and the corners of the doors and windows are at right angles. When using, just place the square ruler on the corner of the corner or the door and window to see if the two sides match the two sides of the ruler.
6, inspection hammer
This small metal hammer that can be freely retracted is specially used to test the hollow condition of the wall and the ground. The sound produced by the tapping is used to judge whether there is an empty drum on the wall.
7, test socket
The test socket is an indispensable tool for testing whether the line sequence in the circuit is normal. There are three indicator lights on the test socket, which show the zero line, ground line and fire line from left to right. When the two indicators on the right are on at the same time, it means that the circuit is normal. When all three lights are off, it means there is no phase line in the circuit; only the middle light is on, it means the ground wire is missing; only the right light is on, it means zero. line.
The above is a detailed answer to the house acceptance, I do not know if you are satisfied with the introduction of the decoration home network Xiaobian. If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
How to check the rough house? Blank house acceptance considerations
Plastic steel door and window acceptance standard plastic steel door and window maintenance method
What are the procedures for buying a house? How to accept new homes?
How to install the hydraulic press? Hood installation and acceptance
Home decoration hydropower transformation acceptance acceptance considerations
Door Skin,Exterior Door Skins,Door Skins For Sale,Door Skin For Door
Xiamen XMillion Co.,Ltd. , https://www.xmilliondoor.com